Sometimes you just need to reset your VicoHome camera for various reasons.
For instance, if it’s not connecting to Wi-Fi, shows offline, or isn’t responding, a reset might do the trick.
Besides, if you’re moving the camera to a new network or location, a reset is often necessary.
Overall, a reset can fix a lot of common problems and keep your VicoHome camera running smoothly.
VicoHome provides a range of camera models. And each one has a slightly different reset process.
In this guide, you’ll learn how to reset all models of VicoHome camera – Battery camera, camera without battery, doorbell camera, and more!
Before you reset
Of course, you’d want to fix your device as quickly as possible.
However, before you reset, you should try to unplug it for a few minutes before plugging it back in.
If that doesn’t fix it, you can proceed with the reset procedure.
Just know that the reset will erase all the data and settings. And, you’ll need to set it up all over again!
In technical terms, the camera will revert to its default settings.
So, if you’re ready to begin the reset process, follow the steps below based on your camera model.
How to Reset VicoHome Battery Camera (Standard Models)
If you happen to own a VicoHome camera powered by battery, follow the steps to reset it.
Step 1: Go to the location where you’ve installed the camera
Step 2: Now you’ll need to find the reset button
Step 3: The reset button (a small pinhole) should be at the bottom
Step 4: If you can’t see it, open the silicone cover to find it underneath
Step 5: Get the small pin (paperclip) and press it for a few seconds
Step 6: Release the button when you see the indicator lights flashing
Finally, you’ve successfully reset your VicoHome battery camera!
How to Reset PTZ Battery-Powered VicoHome Camera
Pan/Tilt/Zoom, also known as PTZ, is also a battery-powered camera.
The way to reset this security camera varies slightly, mainly because the reset button is positioned in its ball.
Here’s a step-by-step instructions on how to reset it.
Step 1: Take the PTZ camera
Step 2: Look for the reset pinhole at the top of the ball
Step 3: Uncover the silicone part if you can’t locate the pinhole
Step 4: Get the paperclip or a thin pin and press it for a few seconds
Step 5: Release it when the indicator light flashes blue
How to Reset VicoHome Battery Cameras with Removable Shell
Another type of security camera that is battery-powered comes with a removable shell.
If you’ve got this type of model, you can follow the steps below to perform a reset.
Step 1: Hold the camera
Step 2: Pull out the back cover by pressing the buttons
Step 3: You’ll see the rubber part (Inside which there’s a reset button)
Step 4: Find the small pinhole
Step 5: Press the pinhole with a paperclip
Step 6: Release it after a few seconds when you hear the sound
How to Reset VicoHome Doorbell Camera
For a doorbell camera, you’ll need to perform a few extra steps.
It’s not that difficult. You’ll just need to remove the VicoHome doorbell camera.
Here are the steps to do that.
Step 1: Go to the location where you’ve installed the doorbell camera
Step 2: Take the detaching removal pin that comes with it
Step 3: Press the pin into the doorbell’s hole (on the top)
Step 4: Gently pop out the doorbell to remove it
Step 5: Find the reset pinhole under the silicone cover
Step 6: Use the paperclip to press it until the doorbell responds with an indicator
How to Reset Light Bulb Camera
VicoHome light bulb cameras are a type of plug-in camera.
Here’s a step-by-step guide on how to reset plug-in camera models.
Step 1: Hold the camera
Step 2: Locate the Micro-SD card slot
Step 3: Inside the Micro-SD slot, you’ll find the pinhole
Step 4: Use the paperclip to press and hold it down for a few seconds
Step 5: Release it
Hopefully, these steps will help you reset based on your VicoHome security camera model. You can configure the settings after reconnecting the camera.
How to Reconnect VicoHome Security Cameras After Reset
After your camera is restored to its default settings, you’ll need to set it up again.
You can use the manual that comes with your camera to follow the setup instructions.
Or, you can do the following:
Step 1: Launch the VicoHome app on your smartphone
Step 2: Log in to your account if you haven’t already
Step 3: Tap on the “Add a new camera” button
Step 4: Power on the camera using its power button
Note: (For a battery camera, press and hold down the power button for a few seconds. If you’ve got a plug-in camera, plug the camera into the power source.)
Step 5: After a beep and a blue light indicator, start the pairing
Step 6: Confirm the instructions
Step 7: Properly use the camera to scan the QR code
Step 8: Give the camera name and location
And, finally, you’re done reconnecting your VicoHome camera after a reset procedure!
Conclusion
That’s how simple it is to reset any model of VicoHome security cameras. This reset procedure should resolve any technical issues you’re facing. If the problem persists, don’t hesitate to contact VicoHome support.