How to Reset Spypoint Link-Micro LTE (Step-By-Step)

Thinking of capturing the great shots of your game? But your hunting gear – Spypoint Link-Micro Lte – has given up?

Fear not, with a quick reset, you can get your Spypoint camera up and running!

Now, if you don’t know how to reset your Spypoint Link-Micro-LTE, no worries!

In this post, I’ll guide you on how to reset Spypoint link-micro lte step by step!

Plus, I’ll provide bonus troubleshooting tips for Spypoint link micro lte problems!

That said, let’s get started!

Step 1: Launch the Spypoint App

The first step of the reset procedure doesn’t require you to go to the location of your trail camera.

You can easily reset the default settings by going into the Spypoint app.

Here’s how to do that.

Launch the app
Go to the Settings
At the bottom, you should see the “Restore Default Settings”. Tap on it

It should factory default the settings and reboot the Spypoint camera.

Step 2: Remove the batteries

For this step, you’d need to take a trip to the tree to your Spypoint camera.

Once you’re there, turn off the camera before removing the batteries.

Then, open the camera’s battery compartment. And, remove the batteries for about 30 seconds.

Step 3: Reinsert the batteries

Now, reinsert the batteries carefully in their correct position.

Once the batteries are in their correct position, turn on the camera.

Step 4: Wait for the steady green LED light

After you’ve turned on the camera, it’ll go into the sequence of the lights.

Normally, if everything goes right, following the sequence of the lights, it’ll turn into a solid green. It indicates that it has found a good signal and is ready to function!

Once it’s found the signal, all the lights would turn off.

And, you’re done resetting the device!

Spypoint Link Micro LTE problems (Troubleshooting tips)

Being a user of the Spypoint camera, you might run into common problems.

But, don’t worry – you’re not alone!

With some troubleshooting tips, you can easily resolve the common issues with your Spypoint camera.

That said, here are the common problems of Spypoint cameras with troubleshooting tips to fix them.

Spypoint link micro lte blinking orange:

Should you notice a blinking orange light, there may be an issue with the battery.

You should check the status of the battery in the Spypoint app.

Try charging the batteries or put in new AA non-rechargeable Lithium/Alkaline batteries.

Also, make sure you’ve selected the right battery settings in your app.

Next, replace the dead batteries with fresh batteries.

Spypoint link micro lte blinking red:

If the Spypoint camera is stuck at a flashing red light, it means that its battery is running low.

The best way to fix this is to replace the dead batteries with the fresh ones.

Spypoint link micro lte not connecting:

If you find your Spypoint Link Micro LTE not connecting, there are steps you can take to address the issue.

The first step is to check the network and connection. Go to the Spypoint app and check the network settings. The network should be getting signals to work smoothly.

Next, delete the camera from the Spypoint app and reactivate it again!

If the Spypoint camera is still stuck at connecting, you might consider removing the SD Card and batteries. Reinsert them back after a few seconds!

Also, don’t forget to format the SD card!

Lastly, update the firmware, because your app might’ve got a connectivity issue.

Spypoint link micro lte not sending pictures:

Is Spypoint LINK-MICRO-LTE not sending photos to the app? No worries!

Before you try the other troubleshooting tips, ensure you haven’t used up the plan!

Next, ensure that your camera gets a green light with at least three levels of signals.

Also, consider pushing the SIM card behind the battery pack properly. If that doesn’t solve the problem, try placing the camera that has better signals.

Lastly, don’t forget to check the firmware by going into the Spypoint app. Ensure your app is running on the latest firmware!

Spypoint link micro lte Sim ID registered with another email:

If you got your Spypoint camera from another person, there’s a chance it’s registered under their ID.

In that case, you might want to confirm that the person has deleted the device from his account.

Try to contact the person, and ask them to remove the camera from their account. Once done, you can activate it by registering it with your account.

Delete the camera from the app

To delete the app, launch the Spypoint app and go to the settings tab.

You’ll find the “Delete the device” option in it.

Once deleted, you can re-add it back. Tap on the “+” to add a new camera!

Contact Spypoint Support

If you’ve tried every tip and trick, but to no avail – fret not!

Contact Spypoint Support, and let them know about the issue you’re facing with your camera.

If your unit is under warranty, you might even get a replacement!

Wrapping Up

Hopefully, by following the easy reset procedure and troubleshooting tips, you can get your Spypoint Link camera working again.

Remember to always remove the dead batteries and format the Micro-SD card for better performance. Also, don’t forget to update the firmware to get rid of the bugs and other issues!