Honestly, the Tactacam Reveal X is probably the best trail camera out there.
It’s smooth and reliable, and once you set it up on your favorite tree, it does its thing almost flawlessly!
Even the best gear has its off days.
When this little guy acts up, don’t even think about tossing it.
Just perform a quick reset, and it’ll be back in action.
Not sure how to reset your Tactacam? No worries, this post will guide you step by step!
Step 1: Head to the camera’s location
You can’t reset your Tactacam through the app.
So you’ll need to make the trip to where the camera’s set up.
Yeah, it might be a bit of a trek, but it’s the only way to get that reset done!
So be quick and head to the spot to find your trail camera!
Step 2: Get the paperclip
Next up, make sure you bring along a simple but useful tool—a paperclip!
A paperclip, or any pin that’s thin and needle-like, will get the job done.
So whatever you do, don’t forget to grab that paperclip before you head to the trail camera’s spot!
Step 3: Open the camera’s door
Your Tactacam Reveal X has a door that opens up to reveal some extra buttons!
Gently open the camera’s door, and you’ll spot a few important buttons inside.
You’ll also see the connectivity signals and a few other things in there.
For now, your focus should be on the main button for the reset procedure – Setup Mode!
Step 4: Put the cam into setup mode
Look for the button next to the On-Setup-Off label.
Flip it to the setup mode position by turning it on!
The green light should light up, letting you know the camera’s on and ready to go!
Step 5: Find the Reset Button of Tactacam Reveal X
Not sure where the reset button of Tactacam is?
It’s actually a tiny pinhole at the bottom of the camera.
Just open the cam’s door, and you’ll find it there!
Step 6: Press and Hold the Reset Button
Now that you’ve found the reset button, use the paperclip to press it!
Hold it for 10-15 seconds, then release it and you’re good to go!
Step 7: And that’s a wrap
In this last step, your camera should turn off and restart, coming back fresh with no saved settings.
If it doesn’t reboot or restart, just go through the steps again.
Tactacam Troubleshooting tips
The reset procedure is an effective method to fix Tactacam Reveal X when it is acting up.
For example, you might be facing issues like it not responding, trouble connecting, or when the settings seem off.
When that’s the case, it might be the perfect time for a reset!
After all, a quick reset can clear out any glitches and give your camera a fresh start.
Yeah, you might have to make a few trips back and forth to the camera’s location.
But once it’s fixed, you’re all set and won’t have to worry about it anymore!
But what if the reset doesn’t fix things?
If a reset doesn’t do the trick, there are a few things you can try.
First, double-check the batteries. Make sure they’re fresh and properly installed since low power can cause all sorts of frustrating issues.
Ensure you’re using Alkaline, Rechargeable NiMH, or Lithium Ion AA batteries. These are the most compatible battery types for your Tactacam Reveal.
If the battery tray is damaged, make sure to get a replacement!
Then, take a look at the SD card. Make sure it’s compatible, formatted correctly, and not full. A bad or incompatible card can mess things up.
You should also check if there’s a firmware update available for your cam. Updating the software can often fix bugs and improve performance.
Finally, if nothing fixes your problem, don’t stress—just reach out to Tactacam’s customer support for some help!
Final Thoughts
Trail cams acting up is pretty common, but don’t worry—there’s always a way to get them back in action. You just have to figure out what’s causing the issue. Once you nail down the problem, troubleshooting becomes a lot easier.
A quick reset should be your last resort if nothing else works.
Hopefully, this guide helps you sort things out so you can get your Tactacam Reveal X running smoothly!